Powermatic 60B Bedienungsanleitung Seite 1

Operating Instructions and Parts Manual 8-inch Jointer Model 60B WMH TOOL GROUP, Inc. 2420 Vantage Drive Elgin, Illinois 60124 Part N

10 Electrical Connections Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must b

11 IMPORTANT: Make sure the electrical characteristics are the same on the motor nameplate and the power source, and make sure the circuit on which t

12 Adjustments Disconnect machine from power source before making adjustments. Tools required for adjustments: 8mm & 12mm wrenches 4mm hex w

13 Installing Knives Use care when working with or around sharp knives. Make sure power to the machine has been disconnected. When installing new k

14 7. Tightening the gib screws should be done in increments, to prevent any distortion to the cutterhead or buckling of knives. While holding the g

15 6. Tighten the gib screws (A, Figure 18) then back them off approximately 1/4 turn or until the table moves freely, and re-set the lock nuts on t

16 Setting Outfeed Table For accurate work in most jointing operations, the outfeed table must be exactly level with the knives at their highest poin

17 Fence Movement To slide the fence forward or backward on the table, loosen lock handle (A, Figure 24), slide the fence to desired position and tig

18 45 degree forward stop: 1. The 45 degree forward stop is controlled by the screw (E, Figure 25). 2. Loosen the locking handle (B, Figure 25) and

19 Direction of Grain Avoid feeding work into the jointer against the grain. This will result in chipped and splintered edges (Figure 27). Feed with

2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Serv

20 Edge Jointing This is the most common operation for the jointer. Set guide fence square with the table. Depth of cut should be the minimum require

21 Taper Cuts A useful jointer operation is cutting an edge to a taper. The method can be used on a wide variety of work. Tapered legs of furniture a

22 Maintenance Disconnect machine from power source before doing any maintenance. The table and fence surfaces must be kept clean and free of rust

23 IMPORTANT: If the bearings need replacement, this should be done by qualified service personnel. The bearings are press fitted and must be remove

24 Troubleshooting – Operating Problems Trouble Probable Cause Remedy Finished stock is concave on back end. Knife is higher than outfeed table. Rai

25 Troubleshooting – Mechanical and Electrical Problems Trouble Probable Cause Remedy No incoming power. Verify unit is connected to power, on-butto

26 Trouble Probable Cause Remedy Motor failure. If electric motor is suspect, have it tested by qualified service personnel. Repair or replace as ne

27 Parts List: Base Assembly Index No. Part No. Description Size Qty ... 2365022 ...Jointer Base Assembly (Items 1 th

28 57... 6296166...Flat Washer...5/16”...6 59...

29 Base Assembly

3 Table of Contents Warranty and Service...

30 Parts List: Fence Assembly Index No. Part No. Description Size Qty ... 60B-100 ...Fence Assembly (Items 1 thru 33)

31 Fence Assembly

32 Parts List: Cutterhead Assembly Index No. Part No. Description Size Qty ... 60B-300 ...Cutterhead Assembly (Items

33 Parts List: Stand Assembly Index No. Part No. Description Size Qty ... 2365021 ...Stand Assembly (Items 1 thru 47)

34 39... 6823013...Stripe...8 ft. 4

35 Stand Assembly

36 Electrical Connections – 230 Volt, Single Phase

37 Electrical Connections – 230 Volt, 3 Phase

38 Electrical Connections – 460 Volt, Three Phase

39 Preventive Maintenance Checklist for Model 60B Jointer [ ] Work area around machine marked off clearly. [ ] Non-skid floor strips in a

4 Warning 1. Read and understand the entire owner’s manual before attempting assembly or operation. Know the limitations and hazards in using the j

40 WMH Tool Group, Inc. 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.powermatic.com www.wmhtoolg

5 20. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it

6 Familiarize yourself with the following safety notices used in this manual: This means that if precautions are not heeded, it may result in minor

7 Specifications Model Number... 60B ...

8 Receiving Open both shipping crates and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Before ope

9 3. The stand can be secured to the floor using two anchor bolts (not provided) through the holes inside the bottom of the stand. Aligning Pulleys