Powermatic 15HH Bedienungsanleitung

Operating Instructions and Parts Manual 15-inch Planer Models 15S and 15HH WALTER MEIER (Manufacturing), Inc. 427 New Sanford Road LaVergn

10This machine must be grounded. Grounding provides a path of least resistance to help divert current away from the operator in case of electrical ma

11Pulley Alignment The pulleys should be in line for proper belt operation. 1. Remove the belt guard and place a straight edge against the faces of

12IMPORTANT: Be sure that the height of front and rear rollers are the same. And the table rollers must always be set parallel to the table. Cutterhe

13(You can also use any 3mm diameter tool, such as a hex wrench or drill bit for this purpose.) 9. Insert the screws for the first gib, turning the

14Work Table Parallel to Cutterhead The work table is set parallel to the cutterhead at the factory and no further adjustment should be necessary. If

15Anti-Kickback Fingers The anti-kickback fingers (A, Figure 23) are an important safety feature, as they help prevent kickback of stock. They operat

16Outfeed Roller Height 1. Disconnect machine from power source. 2. Make sure the knives are set properly as previously explained under "Knife

17Chip Deflector The chip deflector (B, Fig. 28) keeps wood chips from falling into the outfeed roller. The deflector should be set approximately 1/1

18Depth of Cut The cutting depth scale is a combination inch/metric scale (Figure 33), with a cutting range from 0 to 6" (152.4mm). A manual sca

19The item numbers on this chart are referenced to the surrounding illustrations. No. Position Inspection Interval Suitable Types of Lubricant

2 Warranty and Service Walter Meier (Manufacturing), Inc., warrants every product it sells. If one of our tools needs service or repair, one of our A

20Functions of the Digital Scale (Model 15S only) Figure 40 identifies the parts of the digital scale. The button functions are discussed below, foll

21From this point on, any table movement will be based off this setting. The setting will be kept in the device’s memory even when the digital displa

22Method 2 uses a scrap board and calipers. 1. Turn on the digital display. It turns on in absolute mode. 2. Plane one side of a scrap board at an

23Troubleshooting: Performance Problems Trouble Probable Cause Remedy Snipe. (NOTE: Snipe cannot be eliminated, but can be so minimized as to be neg

24Troubleshooting: Mechanical and Electrical Problems Trouble Probable Cause Remedy Uneven depth of cut side to side. Knife projection from cutterhe

25Trouble Probable Cause Remedy Machine will not start/restart or repeatedly trips circuit breaker or blows fuses. (cont.) Motor starter failure. E

26Troubleshooting: Digital Scale – Model 15S only Trouble Probable Cause Remedy Flashing digits. Low voltage. Replace battery. Locked digits. Hap

27Head Assembly

28Parts List: Head Assembly Index No. Part No. Description Size Qty ... 15S-201 ...Cutterhead Assembly (Items 3 thru

29 53 ... 6284828 ...Handle ...3/8-16NC ... 1 54 .

3 Table of Contents Warranty and Service...

30Base Assembly

31Parts List: Base Assembly Index No. Part No. Description Size Qty 1 ... 6284703 ...Base ...

32Table Assembly

33Parts List: Table Assembly Index No. Part No. Description Size Qty 1 ... 15S-301 ...Table ...

34Gearbox Assembly

35Parts List: Gearbox Assembly Index No. Part No. Description Size Qty ... 6284842 ...Gearbox Assembly (Items 1 thru

36Cabinet Assembly

37Parts List: Cabinet Assembly Index No. Part No. Description Size Qty ... 6284875 ...Cabinet Assembly (Items 1 thru

38Electrical Connections – Single Phase, 230 Volt 95RManAuto969798OR14NOA2174T2 6T32T113NO5L33L2A11L1

39Preventive Maintenance Checklist for Model 15S and 15HH Planers [ ] Work area around machine marked off clearly. [ ] Non-skid floor strip

4 Warning As with all machines, there is a certain amount of hazard involved with the use of this planer. Use the machine with the respect and cauti

40 WALTER MEIER (Manufacturing), Inc. 427 New Sanford Road LaVergne, TN 37086 Phone: 800-274-6848 www.powermat

5 Hand safety. Keep hands outside the machine. NEVER reach under the guards to try to clear stock that stops feeding. Do not clear chips and sawdus

6 Features Figure 1 Specifications Model Number ... 15S ...

7 Unpacking Open container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any sh

8 Installation and Assembly Tools required for assembly: Forklift or hoist with slings 10-12,12-14mm open-end wrenches (provided) 4 and 5mm hex wrenc

9 Extension Tables 1. Mount a cast iron table to the edge of the main table with three M8 x 25 hex cap screws (Figure 9) using a 12mm wrench. Do not