OWNER’S MANUAL Model COS18 Cut-Off Saw Left-Hand model shown, with 8' and 4' optional roller tables
10ELECTRICAL CONNECTIONS WARNING: Electrical connections must be made by a qualified electrician in compliance will all relevant codes. The
11DUST COLLECTION Powermatic recommends the use of a dust collection system with this cut-off saw. The collector should have sufficient capacity (60
127. Re-install clear panel and close blade access door, fastening it securely. NOTE: A sensor switch on the door will automatically shut down the s
13To mount roller tables to saw: 1. Mount an angle bracket to the pre-drilled holes in the side of the saw cabinet with four M8 x 20 hex cap screws
148-FOOT TABLE GUIDE 1. The 8-foot table comes with a guide and scale. The guide should be mounted to the edge of the table with six M8 x 27 square
155. Now place the board flush against the fence and against the rail of the roller table(s). If necessary, shift a roller table horizontally to bri
16BELT REPLACEMENT 1. Release tension on the v-belt and remove old belt. 2. Make sure the new belt is properly situated into the v-grooves of th
17OPTIONAL ACCESSORIES - COS18 Cut-Off Saw Part No. Description 6827037 ... 8' Roller T
18PARTS LIST: Table & Motor Assembly (COS18 Cut-Off Saw) Index Part No. No. Description
19PARTS LIST: Table & Motor Assembly (COS18 Cut-Off Saw) continued Index Part No. No. Description
2 This manual has been prepared for the owner and operators of a Powermatic Model COS18 Cut-Off Saw. Its purpose, aside from proper machine operation
20Table & Motor Assembly – Left Hand (COS18 Cut-Off Saw)
21Table & Motor Assembly – Right Hand (COS18 Cut-Off Saw)
22PARTS LIST: Stand Assembly (COS18 Cut-Off Saw) Index Part No. No. Description
23Stand Assembly – Left Hand (COS18 Cut-Off Saw)
24Stand Assembly – Right Hand (COS18 Cut-Off Saw)
25PARTS LIST: Air Control Assembly (COS18 Cut-Off Saw) Index Part No. No. Description
26Air Control Assembly – Left Hand (COS18 Cut-Off Saw)
27Air Control Assembly – Right Hand (COS18 Cut-Off Saw)
28PARTS LIST: Safety Guard Assembly (COS18 Cut-Off Saw) Index Part No. No. Description
29PARTS LIST: Safety Guard Assembly (COS18 Cut-Off Saw) continued Index Part No. No. Description
3TABLE OF CONTENTS Safety Rules...
30Safety Guard Assembly – Left Hand (COS18 Cut-Off Saw)
31Safety Guard Assembly – Right Hand (COS18 Cut-Off Saw)
32PARTS LIST: 4' Roller Table Assembly (COS18 Cut-Off Saw) #6827038 Optional Accessory Index Part No. No.
334' Roller Table Assembly (COS18 Cut-Off Saw) #6827038 Optional Accessory
34PARTS LIST: 8' Roller Table Assembly (COS18 Cut-Off Saw) #6827037 Optional Accessory Index Part No. No.
358' Roller Table Assembly (COS18 Cut-Off Saw) #6827037 Optional Accessory
36PARTS LIST: Pneumatic Diagram (COS18 Cut-Off Saw) Index Part No. No. Description
37PARTS LIST: Pneumatic Diagram (COS18 Cut-Off Saw) continued Index Part No. No. Description
38ELECTRICAL SCHEMATIC (COS18 Cut-Off Saw)
39Preventive Maintenance Checklist for Model COS18 Cut-Off Saw [ ] Work area around machine marked off clearly. [ ] Non-skid floor strips in
4 SAFETY RULES As with all machines, there is a certain amount of hazard involved with the use of this cut-off saw. Use the machine with the respect
40 WMH Tool Group 427 Sanford Road LaVergne, TN 37086 Phone:(800) 248-0144 Fax: (800) 274-6840 E-mai
5Job completion. If the operator leaves the machine area for any reason, the cut-off saw should be turned "off" and the blade should come
6 SAFETY Familiarize yourself with the location and content of these decals on your machine. FIGURE 1
7SPECIFICATIONS: COS18 Cut-Off Saw Stock number (COS18L)...
8FEATURES: COS18 Cut-Off Saw FIGURE 2
9RECEIVING Open shipping crate and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Before using t
Kommentare zu diesen Handbüchern