Powermatic 2800 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Werkzeug Powermatic 2800 herunter. Powermatic 2800 User Manual [en] Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 24
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Operating Instructions and Parts Manual
18-inch Variable Speed Drill Press
Model 2800
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60124 Part No. M-1792800
Ph.: 800-274-6848 Revision B 03/07
www.wmhtoolgroup.com Copyright © WMH Tool Group
Seitenansicht 0
1 2 3 4 5 6 ... 23 24

Inhaltsverzeichnis

Seite 1 - Model 2800

Operating Instructions and Parts Manual 18-inch Variable Speed Drill Press Model 2800 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 P

Seite 2 - Warranty and Service

10Installing Arbor and Chuck 1. Disconnect machine from power source. 2. Thoroughly clean the entire arbor and the inside of the chuck (Figure 9) w

Seite 3 - Table of Contents

11Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surf

Seite 4 - Warning

124. The drill press must comply with all local and national codes after the 230 volt plug is installed. 5. The drill press with a 230-volt plug sh

Seite 5

13Table Extensions Loosen the handles (C, Figure 15) and slide the extensions outward, then re-tighten the handles. Changing Spindle Speeds Change

Seite 6 - Specifications

146. Make sure the coil spring cover is pushed back in, then tighten the two hex nuts (D). Do not over tighten. The hex nuts should be tightened aga

Seite 7 - Unpacking

15Repeat step 5, if necessary, until the light and marking are aligned. 6. Adjust the other laser in the same manner. Two parallel laser markings sh

Seite 8 - Assembly

16Maintenance Before doing maintenance on the machine, disconnect it from the electrical supply by pulling out the plug or switching off the main sw

Seite 9

17Trouble Probable Cause Remedy Noisy Operation (cont.) Noisy motor. Check motor bearings or for loose motor fan. Wood splinters on the underside. N

Seite 10 - Grounding Instructions

18Model 2800 Drill Press

Seite 11

19Parts List: Model 2800 Drill Press Index No. Part No. Description Size Qty 1... PM2800-001 ...Strain Relief...

Seite 12 - Adjustments

2Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Servi

Seite 13 - Return Spring

2057... PM2800-057 ...Rack Ring... 1 58

Seite 14 - Laser Adjustment

21117... PM2800-117 ...Bracket... 1 1

Seite 15 - Operation

22178... TS-152706...Hex Wrench ...5 mm... 1 179...

Seite 16 - Troubleshooting

23Electrical Connections

Seite 17 - Replacement Parts

24Electrical Connections

Seite 18 - Model 2800 Drill Press

3Table of Contents Warranty and Service ...

Seite 19

4 Warning 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on th

Seite 20

5 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious i

Seite 21

6Introduction This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for a Powermatic Model 2800 Drill Pres

Seite 22

7Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discar

Seite 23 - Electrical Connections

8Assembly Tools required for assembly: Cross-point (Phillips) screwdriver Rubber mallet Wrenches – 17, 18 and 24 mm Set of hex (Allen) wrenches Expo

Seite 24

93. Slide the large handle onto the spindle of the table bracket (Figure 4), and tighten the set screw in the handle with a 3mm hex wrench. Crank th

Kommentare zu diesen Handbüchern

Keine Kommentare